Four systems, four sets of problems
The water supply system brings clean water in under pressure. Its problems are leaks, low pressure and burst pipes. The drain system carries waste away by gravity. Its problems are clogs, slow drains and backups. The hot water system heats the water. Its problems are no hot water, leaks and noise. The fixtures are where you touch the system. Their problems are drips, running toilets and weak flow.
Naming the system helps you pick the right service. A pressure problem is not a drain problem, and a water heater leak is not a pipe leak. When you call, describe the symptom and what you have already tried.
What to fix first
| Priority | Problem | Why | Where to read more |
|---|---|---|---|
| Now | Burst pipe or spreading water | Property damage grows by the minute | Burst pipe repair. |
| Now | Sewage backup | Health hazard | Drain cleaning. |
| Now | Gas smell | Safety: leave and call the gas utility | Gas utility or 911. |
| Soon | Leaking water heater | Tank can fail without warning | Water heater repair. |
| Soon | Hidden leak or high bill | Waste and damage | Leak detection. |
| Schedule | Dripping faucet or running toilet | Waste and noise | Faucet repair. |
| Plan | Aging pipe | Prevents repeat failures | Repiping. |
Pressure is the quiet cause of many repairs
High water pressure wears out fixtures, valves and the water heater. The California Plumbing Code material the City of Milpitas distributes calls for a pressure regulator when pressure exceeds 80 psi. A gauge on a hose bib tells you the number in a minute. If it reads above 80, the regulator needs attention, and fixing it prevents more repairs.
Low pressure has different causes. A partly closed valve, a clogged aerator, a failing service line or corroded galvanized pipe can all lower flow. Test at an outdoor spigot first. If pressure there is fine and a fixture is weak, the problem is local to that fixture. If pressure is low everywhere, it points to the supply side. See water line repair.
Repairs a homeowner can reasonably do
- Replace a toilet flapper or fill valveParts are inexpensive and instructions are on the package.
- Clean an aeratorUnscrew it, rinse out minerals and reattach.
- Replace a faucet cartridgeTurn off the supply first.
- Replace a supply line under a sinkTurn the stop valve off first and use braided lines.
- Clear a simple sink clog with a plungerUse a cup plunger and a wet cloth to seal other openings.
- Flush the water heaterOnce a year, following the manual.
Repairs better left to a plumber
- Anything involving the main water line or sewerMistakes are costly and permit rules apply.
- Water heater replacementGas, venting and strapping must be done to code. See water heater replacement.
- Pipe replacement inside wallsIt needs a permit and inspection.
- Repeat clogsA camera finds the cause. See sewer camera inspection.
- Slab leaksNeed detection tools. See slab leak repair.
- Gas workOnly a qualified plumber should touch gas piping.
Want a plumber to handle it?
Call and a person answers, any hour. You hear the price before any work starts.
What the City of Milpitas says is exempt from a permit
The city's Building Safety FAQ says that repairs which do not replace or rearrange pipes do not need a plumbing permit. Fixing a leaking joint, swapping a faucet cartridge or clearing a drain falls under that. Replacing a section of pipe, a water heater or a fixture connection that changes the layout is different and needs a permit.
Knowing the line helps you plan. A small repair done today is permit-free. A larger project later needs a permit and an inspection. We tell you which side of the line a job falls on before work starts. If you live in North San Jose, our San Jose service page covers the City of San Jose permit rules, which are separate.
Source type: City of Milpitas Office of Building Safety FAQ and permit handout.
A repair routine that saves money
Learn your shutoffs
Find the main water valve and each fixture stop valve.
Check pressure once a year
A cheap gauge on a hose bib is enough.
Look under sinks every few months
Catch drips before they rot the cabinet.
Flush the water heater yearly
It reduces sediment and extends tank life.
Photograph repairs and keep receipts
It helps with resale and insurance.
Keep a plumbing file for the house
A folder with receipts, permit numbers, the water heater label and photos of the shutoff valves makes every future repair easier. A plumber who knows what was done before can skip guesswork. A buyer, an insurer or the city may also ask for records of major work.
Add the date and the name of whoever did the work. Add a photo of the pipe before walls are closed up, because it is the only record of what is inside the wall once the drywall goes back on. Five minutes at the time of a repair saves hours later.
When a repair is really a replacement
If you keep fixing the same fixture, the money spent adds up. A toilet that clogs monthly, a faucet whose parts are no longer sold and a water heater with its third repair are all candidates for replacement. A good plumber will say so when a repair is not the best use of your money.
We would rather tell you honestly. Call (510) 544-1962 and describe the problem. We give you the options, the prices and our recommendation, and then you decide.
Sources
The 80 psi regulator rule comes from the City of Milpitas Office of Building Safety handout, which cites the California Plumbing Code, which is based on the Uniform Plumbing Code (UPC).
Common Questions
Replacing or rearranging pipes, replacing a water heater and installing new fixtures need one. Simple repairs without pipe replacement are exempt.
It is usually where the water line enters the house, near the front hose bib or in the garage. There is also a valve at the meter.
Between 40 and 80 psi is typical. The code calls for a regulator above 80 psi.
Policies differ. Sudden water damage is often covered, and worn-out pipes are not. Ask your agent.
Yes. Our emergency line is open 24/7.
